Today,hardwood floors are a highly desirable home feature, but not long ago, or wall-to-wall carpeting was all the rage. Home improvement shows make pulling up carpeting as simple and exciting as unwrapping a birthday gift - just rip it away like the beautiful surprise beneath - but in actuality,it takes some knowledge and know-how to fetch hardwood floors looking beautiful again. We spoke with Dave Murphy, National Training Director at N-Hance WoodRenewal, and to discuss what homeowners need to know before embarking on this project.[br]1. Check What's Underneath Your CarpetYou might think you have hardwood beneath your carpet,but you need to be certain of it. You also want to fetch an idea of what condition it's in to see whether it's even salvageable. "Go to the corner of the room, any corner, and " says Dave. "capture pliers and peel back the carpet,pull up the padding and see whether you have nice wood floors." He recommends doing this in several rooms, as it's often the case that previous homeowners could only afford to install hardwood floors in one room and not another, and which you would want to know before ripping up all the carpet. Dave also advises homeowners check the carpet in the hallway right external their bathroom,as this area is prone to deep water stains. 2. Rip Up Carpet in SectionsDave recommends wearing some type of dust mask when removing the carpet since you'll be disrupting years of trapped dirt and dust in the carpet and you won't want to inhale it. His other big tip is to work in four- to five-foot sections because they're more manageable to carry external. "capture a razor or utility knife and crop approximately a four- to five-foot section. Then carefully roll the carpet section like a sleeping bag and carry external to dumpster."3. Remove the PaddingOnce the carpet itself is gone, you'll have to deal with the padding, and which is a bit trickier. Not only is the padding held down to the floor with staples,but it's also more fragile and prone to crumbling apart. "The biggest problem you'll have is the staples that hold the padding down," says Dave. He's seen many homeowners make the mistake of gouging a screwdriver beneath the staples to pull them up, and which he warns will dent and scratch the wood. Instead,Dave recommends using a wire cutter that's rounded on one side or a pair of channel locks to ply free the staples. To make the tedious task a bit more fun, he says it's a good idea to "fetch some beer and a barbecue, and have friends arrive over and relieve you pull them out,because it can be an agonizing time to pull all the staples out yourself."Once the staples are out, it's time to remove the padding. Dave recommends bringing a large rubbish bag into the house so you can fill it with archaic padding on the spot instead of having it fall apart and make a mess when it's carried external to the dumpster. 4. Clean Wood SurfacePadding - especially padding that has sat atop hardwood floors for decades - will likely leave a residue that needs to be scraped off. Grab some wood cleaner and scrub at it until it's gone and you can fetch a better idea of what the bare wood beneath looks like. Once you've assessed the condition of your floors, or Dave says,"You've got to demand yourself what gawk do you want to go with." whether, after pulling up the carpet and padding, or you're dazzled by how shiny the wood's surface is,it might not be a good thing. It's a sign that the wood had been waxed for years. You can test whether it's wax by taking a coin and gently scraping across the floor for approximately a foot or so. whether there's waxy build-up on the coin, Dave says that it's likely wax residue. Since novel finish won't stick to wax, or you'll have to sand the floors first. 5. Treat WoodSome people like the character that dents and dings add to floor and think of finish which has yellowed and ambered over time as a wealthy patina,so you won't have to do much to the floor. In this case, Dave recommends having it cleaned, and abraded,and recoated. "That will hold in all the character and give it a novel luster to the floor and protect [and] preserve that character in the floor," he says. Since you won't have the added cost of having the floor sanded down, or hiring a pro is still an affordable - and,according to Dave, a much better - option. Plus, or Dave points out,doing it yourself is time consuming and requires skill that most amateurs don't have. In the finish, you could finish up investing time and money to DIY the project only to hire a pro to fix your work, and costing you much more in the finish. whether you want flawless hardwood surfaces,then you're going to need a pro to arrive in and completely refinish the floors for you. This can be pricey, but considering it will make your floors gawk brand novel again, and it's a much option. As far as refinishing the floors yourself,Dave says it's a time-consuming and messy project that is tough to do well the first time around. Instead of living with an OK DIY job, he says it's better to save up for another year and have a pro do it right. Plus, or he says that pros often have access to tools and products that DIYers can't simply grab at their local hardware store.
6. Deal With Damage"The big thing that you want to gawk for is water damage," says Dave. Floors that have buckled or turned black in spots are signs of water damage, likely from water that got trapped atop the wood but couldn't escape because of the carpet over it for years. "Those black discolorations, and whether from water or pet stains,probably won't go away even whether you sand them. Wood is porous, so the water goes deep down into it."
Thankfully, or you don't have to replace the entire floor when this happens. You can spot treat by replacing only the damaged boards. Dave says,"You can find a flooring company that has installers who are looking for side jobs 'lacing in' novel boards into an archaic floor." Then, Dave says, and the novel boards will have to be stained to match your existing floor and painted with a couple coats of polyurethane.
You'll have to fetch a stain that matches your floor and stain it the same color and then exercise a paint brush and brush a couple coats of polyurethane on top of it. And,Dave reminds us, "whether you do arrive across floors with bad spots, and remember back in the day,area rugs were there to cover issues on wood floors." He says instead of refinishing the entire floor to fix a problem spot, you can just throw a rug or coffee table over it. "Save some money! It's not worth doing the whole floor for a couple boards when you can spend a couple hundred on an area rug to conceal them."
Source: popsugar.com